A grey driftwood branch arcs upward from a solid oak block beside your armchair, curving overhead like a crane bending toward water. At the tip, a tilted mushroom cap hangs face-down, its hand-carved gill lines projecting a warm cone of golden light directly onto your book, your lap, and the armrest of the chair. The braided cloth cord follows the driftwood's curve, winding along the bark-stripped surface like a vine climbing a branch.
Arc Driftwood Stem
The stem is a single piece of naturally arching driftwood, selected for its long sweeping curve that reaches outward and overhead from the base. The arc is wide enough to extend the cap over a seated reader without the base sitting directly behind the chair. The grey-silver surface is stripped of bark by natural weathering, with knot stubs, branch scars, and smooth worn sections along its length. The driftwood is cleaned, treated, and sealed to preserve its raw form. A braided cloth cord is routed along the outer curve of the stem, held in place by small hand-forged clips that follow the natural contours of the wood. The visible cord becomes part of the design rather than something to hide.
Tilted Gill Glow Cap
The cap is mounted at the end of the arc at a downward angle, facing the reader below. The shape is an asymmetric dome, higher on the back edge and lower on the front, following the natural tilt of a shelf fungus growing from a leaning branch. The top surface is polished smooth in warm golden tones with flowing grain and natural knots. Underneath, hundreds of tight gill lines are carved by hand from the center outward. The built-in LED shines through the carved channels in a focused, directional cone of warm 2700K light. Because the cap tilts downward rather than sitting level, the light concentrates on the reading area below rather than spreading in all directions. Dimmable from full task lighting for reading to a low ambient glow for evenings.
Solid Oak Block Base
The base is a rectangular block of solid oak with clean, squared edges and a smooth sanded surface. The warm honey tone of the oak contrasts with the grey driftwood above. The block is heavy and dense, serving as a counterweight to balance the arching driftwood and the cap at the far end. A foot dimmer switch sits on the floor beside the cord where it exits the base.
Specifications
  • Material: Naturally arching driftwood (stem) + solid wood (cap) + solid oak (base)
  • Light: Built-in LED, warm white (2700K), dimmable
  • Power: Braided cloth cord with foot dimmer, routed along stem
  • Stem: Arc driftwood, cleaned, treated, sealed, with cord clips
  • Cap: Tilted asymmetric dome with hand-carved gill detail
  • Base: Solid oak block, counterweighted
  • Finish: Natural oil on cap and base. Clear seal on driftwood.
  • Arc reach: 24-32" outward from base (varies by size)
Placement
Built for a living room reading chair, a bedroom armchair, a home library reading nook, or a study. The arc places the light directly above a seated reader without a table, shelf, or overhead fixture. Also works beside a sofa for side lighting, or in a nursery for a soft overhead glow during bedtime reading. The oak block base tucks behind or beside the chair.
Care
Wipe the polished cap with a slightly damp cloth. Reapply wood oil once a year. Dust the driftwood stem with a soft dry brush. Check the cord clips periodically. LED needs no maintenance. Avoid excessive moisture.
Handcrafted by Vietnamese artisans. The arcing driftwood is sourced from naturally fallen wood and selected by hand for its sweeping curve, structural strength, and visual character. Every gill line on the cap is carved individually. No molds. No CNC machines. No two lamps will ever look the same.
Need a different size or arc reach? Contact our team to discuss custom height, reach, cap angle, or finish preferences.
✔️ Preview your design before production
✔️ Free shipping
✔️ 30-day satisfaction guarantee

Furniture Placement

  •  Position your furniture away from direct sunlight, or use blinds or curtains to reduce sun exposure.
  •  Always set your furniture on a level surface to preserve its balance and structure.

Cleaning & Upkeep

  •  Regularly wipe down your furniture with a soft, dry, or slightly damp cloth.
  •  Avoid using harsh chemicals like bleach or ammonia, as these can ruin the finish and damage the wood.

Weight Capacity & Use

  •  Respect the recommended weight limit for each piece to ensure its durability.
  •  When moving furniture, lift it instead of dragging or pushing to prevent surface scratches or joint damage.

Preventing Mold & Mildew

  •  Quickly wipe up any spills to stop moisture from penetrating the wood.
  •  In areas with high humidity, use a dehumidifier to maintain an ideal moisture balance.

Free Shipping On All Orders

Standard shipping is free on every order, with no minimum purchase required.

Estimated Crafting & Delivery Times

  • Processing & Crafting: Typically 7–14 business days, depending on the piece and design complexity.
  • Transit Time: Approximately 5–7 business days after dispatch, depending on your destination and carrier.
  • Estimated Total: Approximately 12–21 business days. Customer review time and agreed revisions may extend this estimate.
  • Duties & Taxes: Delivered Duty Paid (DDP) — Ashdeco covers all import duties, taxes and customs fees.

For made-to-order and personalised pieces, we share photos or videos for your review before finishing and again before dispatch. Finishing begins after you approve the unfinished piece. We pack and ship only after you approve the finished version.

Returns: 30-Day Return Policy, Eligible Issues

If your piece arrives damaged, defective or incorrect due to a fulfillment error, please contact support@ashdeco.com within 30 calendar days of delivery, including your order number and photos. We will review your claim and arrange an appropriate return or replacement. Return shipping for approved claims is fully covered by Ashdeco.

Please note: Made-to-order and personalised pieces are not eligible for returns due to a change of mind or personal preference. This does not affect support for damaged, defective or incorrect items. Please contact us before returning any piece.

Thy Tran Crafted by

Thy Tran

Arc Driftwood Reading Mushroom Floor Lamp with Tilted Gill Glow

SKU: ASPF070426-49
5 out of 5 stars with 400+ reviews 30 Questions
$2,280.00
10% Get 10% off orders $2,000+
Choose your sizeRequest a free consultation15"W x 25"D x 60"H
Choose your wood tone As pictured
Choose your finish Smooth Surface
Free Shipping - Easy Assembly
30-Day Returns
1-Year Warranty
Shipping Insurance
Share:
Thy Tran Crafted by

Thy Tran
Arc Driftwood Reading Mushroom Floor Lamp with Tilted Gill Glow
SKU: ASPF070426-49
5 out of 5 stars with 400+ reviews 30 Questions
$2,280.00
10% Get 10% off orders $2,000+
Choose your sizeRequest a free consultation15"W x 25"D x 60"H
Choose your wood tone As pictured
Choose your finish Smooth Surface
Free Shipping - Easy Assembly
30-Day Returns
1-Year Warranty
Shipping Insurance
A grey driftwood branch arcs upward from a solid oak block beside your armchair, curving overhead like a crane bending toward water. At the tip, a tilted mushroom cap hangs face-down, its hand-carved gill lines projecting a warm cone of golden light directly onto your book, your lap, and the armrest of the chair. The braided cloth cord follows the driftwood's curve, winding along the bark-stripped surface like a vine climbing a branch.
Arc Driftwood Stem
The stem is a single piece of naturally arching driftwood, selected for its long sweeping curve that reaches outward and overhead from the base. The arc is wide enough to extend the cap over a seated reader without the base sitting directly behind the chair. The grey-silver surface is stripped of bark by natural weathering, with knot stubs, branch scars, and smooth worn sections along its length. The driftwood is cleaned, treated, and sealed to preserve its raw form. A braided cloth cord is routed along the outer curve of the stem, held in place by small hand-forged clips that follow the natural contours of the wood. The visible cord becomes part of the design rather than something to hide.
Tilted Gill Glow Cap
The cap is mounted at the end of the arc at a downward angle, facing the reader below. The shape is an asymmetric dome, higher on the back edge and lower on the front, following the natural tilt of a shelf fungus growing from a leaning branch. The top surface is polished smooth in warm golden tones with flowing grain and natural knots. Underneath, hundreds of tight gill lines are carved by hand from the center outward. The built-in LED shines through the carved channels in a focused, directional cone of warm 2700K light. Because the cap tilts downward rather than sitting level, the light concentrates on the reading area below rather than spreading in all directions. Dimmable from full task lighting for reading to a low ambient glow for evenings.
Solid Oak Block Base
The base is a rectangular block of solid oak with clean, squared edges and a smooth sanded surface. The warm honey tone of the oak contrasts with the grey driftwood above. The block is heavy and dense, serving as a counterweight to balance the arching driftwood and the cap at the far end. A foot dimmer switch sits on the floor beside the cord where it exits the base.
Specifications
  • Material: Naturally arching driftwood (stem) + solid wood (cap) + solid oak (base)
  • Light: Built-in LED, warm white (2700K), dimmable
  • Power: Braided cloth cord with foot dimmer, routed along stem
  • Stem: Arc driftwood, cleaned, treated, sealed, with cord clips
  • Cap: Tilted asymmetric dome with hand-carved gill detail
  • Base: Solid oak block, counterweighted
  • Finish: Natural oil on cap and base. Clear seal on driftwood.
  • Arc reach: 24-32" outward from base (varies by size)
Placement
Built for a living room reading chair, a bedroom armchair, a home library reading nook, or a study. The arc places the light directly above a seated reader without a table, shelf, or overhead fixture. Also works beside a sofa for side lighting, or in a nursery for a soft overhead glow during bedtime reading. The oak block base tucks behind or beside the chair.
Care
Wipe the polished cap with a slightly damp cloth. Reapply wood oil once a year. Dust the driftwood stem with a soft dry brush. Check the cord clips periodically. LED needs no maintenance. Avoid excessive moisture.
Handcrafted by Vietnamese artisans. The arcing driftwood is sourced from naturally fallen wood and selected by hand for its sweeping curve, structural strength, and visual character. Every gill line on the cap is carved individually. No molds. No CNC machines. No two lamps will ever look the same.
Need a different size or arc reach? Contact our team to discuss custom height, reach, cap angle, or finish preferences.
✔️ Preview your design before production
✔️ Free shipping
✔️ 30-day satisfaction guarantee

Furniture Placement

  •  Position your furniture away from direct sunlight, or use blinds or curtains to reduce sun exposure.
  •  Always set your furniture on a level surface to preserve its balance and structure.

Cleaning & Upkeep

  •  Regularly wipe down your furniture with a soft, dry, or slightly damp cloth.
  •  Avoid using harsh chemicals like bleach or ammonia, as these can ruin the finish and damage the wood.

Weight Capacity & Use

  •  Respect the recommended weight limit for each piece to ensure its durability.
  •  When moving furniture, lift it instead of dragging or pushing to prevent surface scratches or joint damage.

Preventing Mold & Mildew

  •  Quickly wipe up any spills to stop moisture from penetrating the wood.
  •  In areas with high humidity, use a dehumidifier to maintain an ideal moisture balance.

Free Shipping On All Orders

Standard shipping is free on every order, with no minimum purchase required.

Estimated Crafting & Delivery Times

  • Processing & Crafting: Typically 7–14 business days, depending on the piece and design complexity.
  • Transit Time: Approximately 5–7 business days after dispatch, depending on your destination and carrier.
  • Estimated Total: Approximately 12–21 business days. Customer review time and agreed revisions may extend this estimate.
  • Duties & Taxes: Delivered Duty Paid (DDP) — Ashdeco covers all import duties, taxes and customs fees.

For made-to-order and personalised pieces, we share photos or videos for your review before finishing and again before dispatch. Finishing begins after you approve the unfinished piece. We pack and ship only after you approve the finished version.

Returns: 30-Day Return Policy, Eligible Issues

If your piece arrives damaged, defective or incorrect due to a fulfillment error, please contact support@ashdeco.com within 30 calendar days of delivery, including your order number and photos. We will review your claim and arrange an appropriate return or replacement. Return shipping for approved claims is fully covered by Ashdeco.

Please note: Made-to-order and personalised pieces are not eligible for returns due to a change of mind or personal preference. This does not affect support for damaged, defective or incorrect items. Please contact us before returning any piece.

Share:
Arc Driftwood Reading Mushroom Floor Lamp with Tilted Gill Glow
$2,280.00

The character is in
the details.

Smooth surface
Smooth surface

A polished, satin-smooth top with a soft sheen. Sealed with a clear protective topcoat for moisture resistance and easy daily care.

Natural rough surface
Natural rough surface

A flat, tactile surface that shows the grain, knots and open pores of the wood. Sealed with a thin matte coat to keep its raw, hand-touched character.

Finish options vary by piece.

A thoughtful fit for your home.

Book a consultation
01

Share your space

Tell us about your room and what you have in mind.

02

Discuss size & finish

We'll guide you through options that fit your home.

03

Confirm the details

Review and finalize your piece with confidence.

An Ashdeco tree-shaped wall bookshelf with fairy lights and ornaments on a green wall, beside a leather armchair, a small tree and wrapped gifts

THE HOLIDAY EDIT

Warmth that stays
beyond the season.

Timeless pieces for more meaningful gatherings at home.

Handcrafted / Factory-made

The difference is in the details.

A closer look at how your piece takes shape.

Wood character

Wood character

Ashdeco

Shaped around the grain.

Typical factory-made

Made to a repeatable design.

The maker

The maker

Ashdeco

A maker you can name.

Typical factory-made

A production team.

Size & finish

Size & finish

Ashdeco

Options for this piece.

Typical factory-made

Set catalog choices.

Explore the craftsmanship

Options vary by piece.

From the workshop to your home

Order Process
& Delivery.

A clear path from first review to final approval.

Made to order with customer approval at each key stage

Your approval comes before shipping.

We pack and ship only after you approve the finished piece.

Have a date in mind?Ask us before ordering

Track your order

Soul of wood

No two tables are ever the same

Every plank carries its own grain, color, and knots. These aren't flaws - they are time's signature, the fingerprint of a tree that lived for decades. When you touch a Ashdeco table, you're touching the years it stood through.

Natural walnut grain with flowing pattern - the unique fingerprint of each plank
Walnut · 1 of 1
Light oak grain with fine, even texture
Oak grain
Natural knot - the mark of a branch that once grew from the trunk
Natural knot
Live edge preserving the tree's natural silhouette
Live edge
Annual growth rings - every ring is one year of the tree's life
Annual rings
100%
Each tabletop is one of a kind - there is no second copy anywhere on Earth
30-80 yrs
Average age of the tree - every grain ring is a season it lived through
0 defects
Knots, mineral streaks, and grain shifts are signatures - never manufacturing flaws
You may also like

More from Driftwood Floor Lamp

View all

What people are searching

Frequently asked questions

Everything you need to know about our pieces, commissions, and care.

How long until my piece arrives?

Shipping itself is quick: 5 to 7 business days once your piece leaves our workshop. Most of the time goes into crafting your piece and your photo approval. We craft your piece, send you photos to approve, and ship it after you approve. Crafting and approval usually take 7 to 14 business days, so the estimated total is 12 to 21 business days. A slow photo approval can extend this. During holidays or busy periods it may take longer, and if there is a significant delay we will email you. All shipments include tracking and insurance.

Do you ship internationally?

Yes, we ship worldwide. We offer free shipping on all orders.

How long does a commission take?

4-8 weeks depending on complexity. A 6-seater dining table takes ~6 weeks, a console cabinet ~4 weeks, a large sideboard ~8 weeks.

Start a commission
How do I take care of my wood piece?

Wipe with a damp cloth. Do not use chemicals. Apply wood oil 1-2 times per year (we include a starter bottle). Avoid direct sunlight and big humidity changes.

What if my piece develops cracks?

Wood expands and contracts with humidity. Minor cracks are natural and part of the material. Major cracks within the first year: we fix free. After 1 year, we charge labor only.

Can I return a piece?

Yes, within 30 days of delivery if your piece has a manufacturer defect or was damaged in shipping. To start, email support@ashdeco.com with your order number and the reason. For defective, damaged or incorrect items we send a prepaid return label and cover return shipping. Once we receive and inspect the returned piece, we send a replacement or a refund. Refunds are processed within 2 business days after we receive your return. Custom or personalized pieces cannot be returned. See our full Refund Policy for exchanges and other details.

Can't find your answer?

Get in touch